Question Details

(solution) I need help all the boxes need to be answered thiss is the


I need help all the boxes need to be answered thiss is the practice getting ready for the final thanks!!!!!!


IMPORTANT: READ THE BOTTOM OF THE LAST PAGE BEFORE YOU BEGIN.

 

CCNA: Introduction to Networks Skills Assessment ? Student Hands-on PRACTICE Final Exam

 

You will use NETLAB (http://netlab1.ivytech.edu) to complete this lab. When you start NETLAB, you will need to open the lab

 

6.4.3.5 so you can open the proper topology. Do NOT load initial configurations. Load a ?clean? configuration.

 

Do NOT use the default

 

lab instructions for

 

Lab 6.4.3.5!

 

Use the lab instructions

 

below. Make sure to click I?m done in NETLAB so that your logs will be emailed to your instructor. These logs will be graded by your

 

instructor as well as your typed answers in this Word document. See the last page for submission instructions. Topology

 

Subnet A Subnet B Assessment Objectives

 

Part 1: Develop the IPv4 Address Scheme (15 points, 20 minutes)

 

Part 2: Initialize and Reload Devices (10 points, 5 minutes)

 

Part 3: Configure Device IPv4 and Security Settings (30 points, 20 minutes)

 

Part 4: Test and Verify IPv4 End-to-End Connectivity (8 points, 10 minutes)

 

Part 5: Configure IPv6 Addressing on R1 (10 points, 10 minutes)

 

Part 6: Test and Verify IPv6 End-to-End Connectivity (7 points, 10 minutes)

 

Part 7: Use the IOS CLI to Gather Device Information (10 points, 10 minutes)

 

Part 8: Save the R1 Configuration to a TFTP Server (10 points, 10 minutes) Scenario

 

In this Skills Assessment (SA) you will configure the devices in a small network. You must configure a router,

 

a switch, and PCs to support both IPv4 and IPv6 connectivity. You will configure security, including SSH, on

 

the router. You will test and document the network using common CLI commands. Finally, you will save the

 

router configuration to a TFTP server. © 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 11 CCNA: Introduction to Networks SA Exam Required Resources 1 Router (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable) 1 Switch (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable) 2 PCs (Windows 7, Vista, or XP with terminal emulation program, such as Tera Term) You will use NETLAB (http://netlab1.ivytech.edu) to complete this lab. When you start NETLAB, you will

 

need to open the lab 6.4.3.5 so you can open the proper topology. Do NOT load initial configurations.

 

Make sure to click I?m done in NETLAB so that your logs will be emailed to your instructor. These logs

 

will be graded by your instructor to arrive at your grade for this exam. Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 2 of 11 CCNA: Introduction to Networks SA Exam Part 1: Develop the IPv4 Addressing Scheme

 

Total points: 15

 

Time: 20 minutes

 

Given an IP address and mask of 10.1.8.0/22, design an IP addressing scheme that satisfies the following

 

requirements.

 

Subnet Number of Hosts Subnet A 333 Subnet B 222 The 0th subnet is used. No subnet calculators may be used.

 

Subnet A

 

Specification Student Input Number of bits in the subnet Points

 

(5 points) IP mask (binary)

 

New IP mask (decimal)

 

Maximum number of usable

 

subnets (including the 0th subnet)

 

Number of usable hosts per subnet

 

IP Subnet

 

First IP Host address

 

Last IP Host address

 

Subnet B

 

Specification

 

Number of bits in the subnet Student Input Points

 

(5 points) IP mask (binary)

 

New IP mask (decimal)

 

Maximum number of usable

 

subnets (including the 0th subnet)

 

Number of usable hosts per subnet

 

IP Subnet

 

First IP Host address

 

Last IP Host address Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 3 of 11 CCNA: Introduction to Networks SA Exam The 0th subnet is used. The network router will use the FIRST IP address in the subnet. The switch will use

 

the SECOND IP address in the subnet. The computers will use the LAST available host addresses for that

 

subnet.

 

Write down the IP address information for each device:

 

Device IP address Subnet Mask Gateway PC-A Points

 

(5 points) R1-G0/0 N/A R1-G0/1 N/A S1 N/A PC-B Points: _________ of 15 Part 2: Initialize and Reload Devices

 

Total points: 10

 

Time: 5 minutes Step 1: Initialize and reload router and switch. (10 points)

 

Erase the startup configurations and VLANs from the router and switch and reload the devices. Task IOS Command Points Erase the startup-config file on

 

the Router. (2 points) Reload the Router. (2 points) Erase the startup-config file on

 

the Switch. (2 points) Delete the vlan.dat file on the

 

Switch (2 points) Reload the Switch. (2 points) Points: __________ of 10

 

Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 4 of 11 CCNA: Introduction to Networks SA Exam Part 3: Configure Device IPv4 and Security Settings

 

Total points: 30

 

Time: 20 minutes Step 1: Configure host computers.

 

After configuring each host computer, record the host network settings with the ipconfig /all command.

 

PC-A Network Configuration

 

Description Points

 

(2 points) Physical Address

 

IP Address

 

Subnet Mask

 

Default Gateway PC-B Network Configuration

 

Description Points

 

(2 points) Physical Address

 

IP Address

 

Subnet Mask

 

Default Gateway Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 5 of 11 CCNA: Introduction to Networks Step 2: SA Exam Configure R1. Configuration tasks for R1 include the following:

 

Task Specification Disable DNS lookup Points

 

(1 point) Router name R1 (1 point) Domain name ccna-lab.com (1 point) Encrypted privileged exec password ciscoenpass (1 point) Console access password ciscoconpass (1 point) Telnet access password ciscovtypass (1 point) Set the minimum length for passwords 10 characters (2 points) Create an administrative user in the local database Username: admin

 

Password: admin1pass (2 points) Set login on VTY lines to use local database (1 point) Set VTY lines to accept ssh and telnet connections only (2 points) Encrypt the clear text passwords (1 point)

 

Use your actual name in the

 

following MOTD:

 

This MOTD was typed by first

 

name last name. (1 point) Interface G0/0 Set the description

 

Set the Layer 3 IPv4 address

 

Activate Interface (2 points) Interface G0/1 Set the description

 

Set the Layer 3 IPv4 address

 

Activate Interface (2 points) Generate a RSA crypto key 1024 bits modulus (2 points) MOTD Banner Step 3: Configure S1.

 

Configuration tasks for R1 include the following:

 

Task Specification Points Switch name S1 (1 point) Configure Management Interface (SVI) Set the Layer 3 IPv4 address (1 point) Encrypted privileged exec password ciscoenpass (1 point) Console access password ciscoconpass (1 point) Telnet access password ciscovtypass (1 point) Points: _________ of 30 Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 6 of 11 CCNA: Introduction to Networks SA Exam Part 4: Test and Verify IPv4 End-to-End Connectivity

 

Total points: 8

 

Time: 10 minutes Step 1: Verify network connectivity.

 

Use the ping command to test connectivity between all network devices.

 

Note: If pings to host computers fail, temporarily disable the computer firewall and retest. To disable a

 

Windows 7 firewall, select Start > Control Panel > System and Security > Windows Firewall > Turn Windows

 

Firewall on or off, select Turn off Windows Firewall, and click OK.

 

Use the following table to methodically verify connectivity with each network device. Take corrective action to

 

establish connectivity if a test fails:

 

From To IP Address Ping Results Points PC-A R1, G0/0 (1 point) PC-A R1, G0/1 (1 point) PC-A S1 VLAN 1 (1 point) PC-A PC-B (1 point) PC-B R1, G0/1 (1 point) PC-B R1, G0/0 (1 point) PC-B S1 VLAN 1 (1 point) In addition to the ping command, what other command is useful in displaying network delay and breaks in the

 

path to the destination? Use that command now on PC-A above. (1 point)

 

_______________________________________________________________________________________

 

Points: _________ of 8 Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 7 of 11 CCNA: Introduction to Networks SA Exam Part 5: Configure IPv6 Addressing on R1

 

Total points: 10

 

Time: 10 minutes

 

Given an IPv6 network address of 2001:DB8:ACAD::/64, configure IPv6 addresses for the Gigabit interfaces

 

on R1. Use FE80::1 as the link-local address on both interfaces. Step 1: Configure R1.

 

Configuration tasks for R1 include the following:

 

Task Specification Points Configure G0/0 to use the first address in subnet A. Assign the IPv6 unicast address

 

Assign the IPv6 link-local address (4 points) Configure G0/1 to use the first address in subnet B. Assign the IPv6 unicast address

 

Assign the IPv6 link-local address (4 points) Enable IPv6 unicast routing. (2 points) Points: _________ of 10 Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 8 of 11 CCNA: Introduction to Networks SA Exam Part 6: Test and Verify IPv6 End-to-End Connectivity

 

Total points: 7

 

Time: 10 minutes. Step 1: Obtain the IPv6 address assigned to host PCs.

 

PC-A IPv6 Network Configuration

 

Description Points

 

(1 point) Physical Address

 

IPv6 Address

 

Default Gateway

 

PC-B IPv6 Network Configuration

 

Description Points

 

(1 point) Physical Address

 

IPv6 Address

 

IPv6 Default Gateway Step 2: Use the ping command to verify network connectivity.

 

IPv6 network connectivity can be verified with the ping command. Use the following table to methodically

 

verify connectivity with each network device. Take corrective action to establish connectivity if a test fails:

 

From To IP Address Ping Results Points PC-A R1, G0/0 (1 point) PC-A R1, G0/1 (1 point) PC-A PC-B (1 point) PC-B R1, G0/1 (1 point) PC-B R1, G0/0 (1 point) Points: _________ of 7 Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 9 of 11 CCNA: Introduction to Networks SA Exam Part 7: Use the IOS CLI to Gather Device Information

 

Total points: 10

 

Time: 10 minutes Step 1: Issue the appropriate command to discover the following information:

 

Description Student Input Router Model Points

 

(2 points) IOS Image File

 

Total RAM

 

Total Flash Memory

 

Configuration Register

 

CLI Command Used Step 2: Enter the appropriate CLI command needed to display the following on R1:

 

Command Description Student Input (command) Points Display a summary of important information

 

about the interfaces on R1. (1 point) Display the IPv4 routing table. (1 point) Display the Layer 2 to Layer 3 mapping of

 

addresses on R1. (1 point) Display detailed IPv4 information about

 

interface G0/0 on R1. (1 point) Display the IPv6 routing table. (1 point) Display a summary of IPv6 interface

 

addresses and status. (1 point) Display information about the devices

 

connected to R1. Information should include

 

Device ID, Local Interface, Hold time,

 

Capability, Platform, and Port ID. (1 point) Save the current configuration so it will be

 

used the next time the router is started. (1 point) Points: _________ of 10 Move on to the next page. © 2013 Cisco and/or its affiliates. All rights reserved. Page 10 of 11 CCNA: Introduction to Networks SA Exam Part 8: Save the R1 Configuration to a TFTP Server.

 

Total points: 10

 

Time: 10 minutes

 

Save the current configuration for R1 to the TFTP Server on PC-A. Tftpd32 software has been installed on

 

PC-A. You will need to start this program before you begin.

 

Description Student Input Points CLI Command (10 Points) Address of remote host

 

Destination Filename

 

Points: _________ of 10 Router Interface Summary Table

 

Router Interface Summary

 

Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2 1800 Fast Ethernet 0/0 (F0/0) Fast Ethernet 0/1 (F0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1) 1900 Gigabit Ethernet 0/0 (G0/0) Gigabit Ethernet 0/1 (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1) 2801 Fast Ethernet 0/0 (F0/0) Fast Ethernet 0/1 (F0/1) Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1) 2811 Fast Ethernet 0/0 (F0/0) Fast Ethernet 0/1 (F0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1) 2900 Gigabit Ethernet 0/0 (G0/0) Gigabit Ethernet 0/1 (G0/1) Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1) Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has.

 

There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible

 

combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific

 

router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be

 

used in Cisco IOS commands to represent the interface. This is the end of your exam. Be sure to click I?m done in NETLAB as your keystrokes

 

will be emailed to the instructor and graded, along with this Word document.

 

Complete the boxes below by typing the information. Leaving these boxes empty will

 

void your submission.

 

Review the answers that you typed into this Word document. No re-takes will be

 

permitted.

 

SAVE and CLOSE this file, naming it LAST NAME NETI105 PRACTICE FINAL (Example:

 

Smith NETI105 Practice Final). Launch Blackboard and attach your file for grading. By typing my name below, I swear that I received no help on this exam in any way. This

 

includes, friends, family, the Internet, calculators, and students (current or past).

 

Tony Gruenloh

 

Full Student Name © 2013 Cisco and/or its affiliates. All rights reserved. c05464928

 

Student C Number 12/13/2015

 

Today?s date Page 11 of 11

 


Solution details:

Pay using PayPal (No PayPal account Required) or your credit card . All your purchases are securely protected by .
SiteLock

About this Question

STATUS

Answered

QUALITY

Approved

DATE ANSWERED

Sep 13, 2020

EXPERT

Tutor

ANSWER RATING

GET INSTANT HELP/h4>

We have top-notch tutors who can do your essay/homework for you at a reasonable cost and then you can simply use that essay as a template to build your own arguments.

You can also use these solutions:

  • As a reference for in-depth understanding of the subject.
  • As a source of ideas / reasoning for your own research (if properly referenced)
  • For editing and paraphrasing (check your institution's definition of plagiarism and recommended paraphrase).
This we believe is a better way of understanding a problem and makes use of the efficiency of time of the student.

NEW ASSIGNMENT HELP?

Order New Solution. Quick Turnaround

Click on the button below in order to Order for a New, Original and High-Quality Essay Solutions. New orders are original solutions and precise to your writing instruction requirements. Place a New Order using the button below.

WE GUARANTEE, THAT YOUR PAPER WILL BE WRITTEN FROM SCRATCH AND WITHIN A DEADLINE.

Order Now